在制作手板之前對手板進行設計對于提高手板質量是非常重要的，實際手板需要考慮到很多因素，如：手板材料的選用。下面濟南手板廠家為您解說。

It is very important to design the hand board before making the hand board to improve the quality of the hand board. Many factors need to be considered in the actual hand board, such as the selection of hand board materials. Next, Jinan Prototype Factory will explain to you.

那么，手板在制作之前需要注意哪些問題呢？下面就由深圳市快速直接工業科技有限公司的產品負責人來簡單講解一下吧。

So, what problems should we pay attention to before making the prototype? Now let's have a brief explanation by the product director of Shenzhen Fast Direct Industrial Technology Co., Ltd.

手板材料的選用既要滿足客戶對產品質量的要求，還應當考慮到材料的成本及其在設計周期內的強度，同時還需根據手板的類型、使用的工作方式、加工速度、主要失效形式等因素來選擇。

The selection of prototype materials should not only meet the customer's requirements for product quality, but also take into account the cost of materials and their strength in the design cycle. At the same time, it should also be selected according to the type of prototype, working mode, processing speed, main failure forms and other factors.

沖裁模的主要失效形式是刃口磨損，就需選擇表面硬度高、耐磨性好的材料；沖壓模主要承受周期性載荷，易引起表面疲勞裂紋，導致表面剝落，就要選擇表面韌性好的材料；

The main failure form of blanking die is edge wear, so it is necessary to select materials with high surface hardness and good wear resistance; Stamping die mainly bears periodic load, which is easy to cause surface fatigue cracks and surface peeling, so it is necessary to select materials with good surface toughness;

拉伸模應選擇摩擦系數特別低的材料；壓鑄模由于受到循環熱應力作用，故應選擇熱疲勞性強的材料。

The drawing die shall be made of materials with very low friction coefficient; Because the die-casting die is subjected to cyclic thermal stress, the material with strong thermal fatigue should be selected.

手板上的各種零件應有足夠的強度及剛度，防止使用過程中損壞和變形，手板上的各種零件應有足夠的強度及剛度，防止使用過程中損壞和變形，緊固零件要有防松動措施，避免意外傷害操作者。不允許在加工過程中發生廢料或工件飛彈現象，影響操作者的注意力，甚擊傷操作者。另外要避免沖裁件毛刺割傷人手。

The various parts on the hand board shall have sufficient strength and stiffness to prevent damage and deformation during use. The various parts on the hand board shall have sufficient strength and stiffness to prevent damage and deformation during use. The fastening parts shall have anti loosening measures to avoid accidental injury to the operator. It is not allowed to produce waste materials or workpiece missiles during processing, which may affect the operator's attention or even injure the operator. In addition, the burrs of blanking parts shall not cut hands.

手板結構的可使用性及性、手板零件的可加工性及手板維修的方便性，這些在設計手板之初都應當盡量考慮得周全一些。更多相關內容就來我們網站http://www.hzbfpg.cn咨詢吧！

The usability and safety of the prototype structure, the processability of the prototype parts and the convenience of the prototype maintenance should be considered as comprehensively as possible at the beginning of the prototype design. More relevant content will come to our website http://www.hzbfpg.cn Consult!